The various activex error codes, and the meaning of the various codes is defined as under.
31712 The two-way port is initializing. Wait a few seconds and redial
31713 No active ISDN lines are available
31714 No ISDN channels are available to make the call
31715 Too many errors occurred because of poor phone line quality
31716 The Remote Access Service IP configuration is unusable
31717 No IP addresses are available in the static pool of Remote Access Service IP addresses
31718 The connection was terminated because the remote computer did not respond in a timely manner.
31719 The PPP connection was terminated by the remote computer
31720 No PPP protocols configured for this connection
31721 The remote computer did not respond
31722 Invalid data was received from the remote computer. This data was ignored
31723 The phone number, including prefix and suffix, is too long
31724 The IPX protocol cannot dial out on the modem (or other connecting device) because this computer is not configured for dialing out (it is an IPX router)
31725 The IPX protocol cannot dial in on the modem (or other connecting device) because this computer is not configured for dialing in (the IPX router is not installed)
31726 The IPX protocol cannot be used for dialing out on more than one modem (or other connecting device) at a time
31727 Cannot access TCPCFG.DLL
31728 The system cannot find an IP adapte
31729 SLIP cannot be used unless the IP protocol is installed
31730 Computer registration is not complete
31731 The protocol is not configured
31732 Your computer and the remote computer could not agree on PPP control protocols
31733 A RAS connection to the remote computer could not be completed. You might need to adjust the protocols on this computer
31734 The PPP link control protocol was terminated
31735 The requested address was rejected by the server
31736 The remote computer terminated the control protocol
31737 PPP Loopback was detected
31738 The server did not assign an address
31739 The authentication protocol required by the remote server cannot use the stored password. Redial, entering the password explicitly
31740 An invalid dialing rule was detected
31741 The local computer does not support the required data encryption type
31742 The remote computer does not support the required data encryption type
31743 The remote computer requires data encryption
31744 The system cannot use the IPX network number assigned by the remote computer
31745 ERROR_INVALID_SMM
31746 SMM_UNINITIALIZED
31747 ERROR_NO_MAC_FOR_PORT
31748 SMM_TIMEOUT
31749 BAD_PHONE_NUMBER
31750 WRONG_MODULE
31751 The callback number contains an invalid character. Only the following 18 characters are allowed: 0 to 9, T, P, W, (, ), -, @, and space
31752 A syntax error was encountered while processing a script
31753 The connection could not be disconnected because it was created by the multi-protocol router
31754 The system could not find the multi-link bundle
31755 The system cannot perform automated dial because this connection has a custom dialer specified
31756 This connection is already being dialed
31757 Remote Access Services could not be started automatically. Additional information is provided in the event log
31758 Internet Connection Sharing is already enabled on the connection
31759 An error occurred while the existing Internet Connection Sharing settings were being changed
31760 An error occurred while routing capabilities were being enabled
31761 An error occurred while Internet Connection Sharing was being enabled for the connection
31762 An error occurred while the local network was being configured for sharing
31763 Internet Connection Sharing cannot be enabled
31764 No smart card reader is installed
31765 Internet Connection Sharing cannot be enabled
31766 A certificate could not be found. Connections that use the L2TP protocol over IPSec require the installation of a machine certificate, also known as a computer certificate
31767 Internet Connection Sharing cannot be enabled. The LAN connection selected as the private network has more than one IP address configured. Please reconfigure the LAN connection with a single IP address before enabling Internet Connection Sharing
31768 The connection attempt failed because of failure to encrypt data
31769 The specified destination is not reachable
31770 The remote computer rejected the connection attempt
31771 The connection attempt failed because the network is busy
31772 The remote computer's network hardware is incompatible with the type of call requested
31773 The connection attempt failed because the destination number has changed
31774 The connection attempt failed because of a temporary failure. Try connecting again
31775 The call was blocked by the remote computer
31776 The call could not be connected because the remote computer has invoked the Do Not Disturb feature
31777 The connection attempt failed because the modem (or other connecting device) on the remote computer is out of order
31778 It was not possible to verify the identity of the serve
31779 To dial out using this connection you must use a smart card
31780 An attempted function is not valid for this connectio
31781 The connection requires a certificate, and no valid certificate was found
31782 Internet Connection Sharing (ICS) and Internet Connection Firewall (ICF) cannot be enabled because Routing and Remote Access has been enabled on this computer
31783 Internet Connection Sharing cannot be enabled. The LAN connection selected as the private network is either not present, or is disconnected from the network. Please ensure that the LAN adapter is connected before enabling Internet Connection Sharing
31784 You cannot dial using this connection at logon time, because it is configured to use a user name different than the one on the smart card. If you want to use it at logon time, you must configure it to use the user name on the smart card
31785 You cannot dial using this connection at logon time, because it is not configured to use a smart card. If you want to use it at logon time, you must edit the properties of this connection so that it uses a smart card
31786 The L2TP connection attempt failed because there is no valid machine certificate on your computer for security authentication
31787 The L2TP connection attempt failed because the security layer could not authenticate the remote computer
31788 The L2TP connection attempt failed because the security layer could not negotiate compatible parameters with the remote computer
31789 The L2TP connection attempt failed because the security layer encountered a processing error during initial negotiations with the remote computer
31790 The L2TP connection attempt failed because certificate validation on the remote computer failed
31791 The L2TP connection attempt failed because security policy for the connection was not foun
31792 The L2TP connection attempt failed because security negotiation timed out
31793 The L2TP connection attempt failed because an error occurred while negotiating security
31794 The Framed Protocol RADIUS attribute for this user is not PPP
31795 The Tunnel Type RADIUS attribute for this user is not correct
31796 The Service Type RADIUS attribute for this user is neither Framed nor Callback Framed
31797 A connection to the remote computer could not be established because the modem was not found or was busy
31798 A certificate could not be found that can be used with this Extensible Authentication Protocol
31799 Internet Connection Sharing (ICS) cannot be enabled due to an IP address conflict on the network. ICS requires the host be configured to use 192.168.0.1. Please ensure that no other client on the network is configured to use 192.168.0.1
Errors 32000-32200 (LDAP)
Error Description
32001 LDAP: Operations error
32002 LDAP: Protocol error
32003 LDAP: Time limit exceeded
32004 LDAP: Size limit exceeded
32005 LDAP: Compare false
32006 LDAP: Compare true
32007 LDAP: Authentication method not supported
32008 LDAP: Strong authentication method required
32009 LDAP: Referral V2
32010 LDAP: Partial results
32011 LDAP: Referral
32012 LDAP: Admin limit exceeded
32013 LDAP: Critical extension unavailable
32014 LDAP: Confidentiality required
32016 LDAP: No such attribute
32017 LDAP: Undefined type
32018 LDAP: Inappropriate matching
32019 LDAP: Constraint violation
32020 LDAP: Attribute or value exists
32021 LDAP: Invalid Syntax
32032 LDAP: Object not found
32033 LDAP: Alias problem
32034 LDAP: Invalid distinguished name syntax
32035 LDAP: Is leaf
32036 LDAP: Alias dereference problem
32048 LDAP: Inappropriate authentication
32049 LDAP: Invalid Credentials
32050 LDAP: Insufficint rights
32051 LDAP: Server busy
32052 LDAP: Server unavailable
32053 LDAP: Unwilling to perform
32054 LDAP: Loop detected
32064 LDAP: Naming violation
32065 LDAP: Object class violation
32066 LDAP: Not allowed on non-leaf entry
32067 LDAP: Not allowed on RDN
32068 LDAP: Already Exists
32069 LDAP: No object class modifications allowed
32070 LDAP: Results to large
32071 LDAP: Affects multiple DSAS
32080 LDAP: Generic Error
32081 LDAP: Server down
32082 LDAP: Local error
32083 LDAP: Encoding error
32084 LDAP: Decoding error
32085 LDAP: Operation timed out
32086 LDAP: Authentication unknown
32087 LDAP: Error in filter
32088 LDAP: User cancelled
32089 LDAP: Invalid parameter
32090 LDAP: Out of memory
32091 LDAP: Connection error
32092 LDAP: Operation not supported
32093 LDAP: No results returned
32094 LDAP: Control not found
32095 LDAP: More results to return
32096 LDAP: Client loop
32097 LDAP: Referral limit exceeded
32101 LDAP: Not connected to server
32102 LDAP: Failed to load WinLDAP library
Errors 33000-34399 (SMS and MMS Toolkit - Misc Errors)
Error Description
33003 Professional license required to use this function
33005 Invalid parameter passed to function
33035 Invalid message class
33036 Invalid message priority
33050 Failed to load provider config file, file not found
33051 Failed to load provider config file, file corrupt
33052 Failed to save provider config file, failed to write file
33060 No more messages in receive buffer
33061 Failed to query message, or invalid messagereference specified
33130 Device used is not a GSM device
33131 Device used does not support GPRS/UMTS
33140 There is no SIM card in the GSM device
33141 SIM card requires PIN code
33142 PIN code entered is invalid
33150 Selected message storage is not available on this GSM device
33151 Device used does not support the storage of SMS delivery report messages
33160 No network coverage, or network busy
33170 SMS service centre (SMSC) address not set
33171 Failed to set SMS service centre (SMSC) address
33201 Failed to connect to SMPP server, please check hostname or IP address
33202 Failed to bind to SMPP server, please check SystemID and Password
33203 Invalid SystemID specified
33204 Invalid Password specified
33205 Not bound to SMPP server, please connect first
33206 SMPP operation timed out
33207 Invalid System Type specified
33208 Failed to send message, currently bound as a receiver
33209 Invalid SMPP version
33210 Failed to cancel SMS message
33211 To receive a deliveryreport, you have to connect as transceiver, not as a transmitter
33215 Failed to submit the SMS message, SMPP provider rejected the message
33216 Recipient address blocked or nut supported by SMPP provider
33217 SMPP Throttling error, please reduce message throughput
33225 Insufficient message credits to submit SMS message
33230 Invalid TLV type specified
33231 Invalid TLV tag specified
33232 TLV parameter not found
33301 Error response received from provider
33302 Unknown response received from provider
33303 URL template for sending text messages not set
33304 URL template for sending data messages not set
33305 URL template for sending unicode messages not set
33460 Invalid UCP provider
33461 No response from UCP provider
33462 Provider reported a syntax error
33463 Provider rejected the message (NACK)
33501 Error during initial negotiation phase
33503 Sending messages to this pager are bared by the provider
33504 Invalid message
33505 Message was sent, but no (N)ACK received
33600 No SNPP provider specified, please check hostname or IP address
33601 Failed to connect to SNPP provider, please check hostname or IP address
33602 Invalid SNPP password
33603 Invalid Pager ID or pincode
33610 SNPP command not supported
33611 No response from SNPP provider, operation timed out
33710 No connection to GPRS/UMTS network, please connect first
33711 Failed to create Dial Up Networking entry for the GPRS/UMTS connection
33712 Generic Dial-up networking error
33720 Missing MMSC server address
33721 Missing GPRS access point name (APN)
33722 Missing WAP gateway address
33730 No response received from WAP gateway
33731 Error response received from WAP gateway
33761 MMSC response: unspecified error
Error-codes-in-activex-controls
Activex-error-codes-1
Activex-error-codes-2
Activex-error-codes-3
Blog-post
Activex-error-codes-4
Activex-error-codes-5
Activex-error-codes-7
Datatable-to-excel-workbook
31712 The two-way port is initializing. Wait a few seconds and redial
31713 No active ISDN lines are available
31714 No ISDN channels are available to make the call
31715 Too many errors occurred because of poor phone line quality
31716 The Remote Access Service IP configuration is unusable
31717 No IP addresses are available in the static pool of Remote Access Service IP addresses
31718 The connection was terminated because the remote computer did not respond in a timely manner.
31719 The PPP connection was terminated by the remote computer
31720 No PPP protocols configured for this connection
31721 The remote computer did not respond
31722 Invalid data was received from the remote computer. This data was ignored
31723 The phone number, including prefix and suffix, is too long
31724 The IPX protocol cannot dial out on the modem (or other connecting device) because this computer is not configured for dialing out (it is an IPX router)
31725 The IPX protocol cannot dial in on the modem (or other connecting device) because this computer is not configured for dialing in (the IPX router is not installed)
31726 The IPX protocol cannot be used for dialing out on more than one modem (or other connecting device) at a time
31727 Cannot access TCPCFG.DLL
31728 The system cannot find an IP adapte
31729 SLIP cannot be used unless the IP protocol is installed
31730 Computer registration is not complete
31731 The protocol is not configured
31732 Your computer and the remote computer could not agree on PPP control protocols
31733 A RAS connection to the remote computer could not be completed. You might need to adjust the protocols on this computer
31734 The PPP link control protocol was terminated
31735 The requested address was rejected by the server
31736 The remote computer terminated the control protocol
31737 PPP Loopback was detected
31738 The server did not assign an address
31739 The authentication protocol required by the remote server cannot use the stored password. Redial, entering the password explicitly
31740 An invalid dialing rule was detected
31741 The local computer does not support the required data encryption type
31742 The remote computer does not support the required data encryption type
31743 The remote computer requires data encryption
31744 The system cannot use the IPX network number assigned by the remote computer
31745 ERROR_INVALID_SMM
31746 SMM_UNINITIALIZED
31747 ERROR_NO_MAC_FOR_PORT
31748 SMM_TIMEOUT
31749 BAD_PHONE_NUMBER
31750 WRONG_MODULE
31751 The callback number contains an invalid character. Only the following 18 characters are allowed: 0 to 9, T, P, W, (, ), -, @, and space
31752 A syntax error was encountered while processing a script
31753 The connection could not be disconnected because it was created by the multi-protocol router
31754 The system could not find the multi-link bundle
31755 The system cannot perform automated dial because this connection has a custom dialer specified
31756 This connection is already being dialed
31757 Remote Access Services could not be started automatically. Additional information is provided in the event log
31758 Internet Connection Sharing is already enabled on the connection
31759 An error occurred while the existing Internet Connection Sharing settings were being changed
31760 An error occurred while routing capabilities were being enabled
31761 An error occurred while Internet Connection Sharing was being enabled for the connection
31762 An error occurred while the local network was being configured for sharing
31763 Internet Connection Sharing cannot be enabled
31764 No smart card reader is installed
31765 Internet Connection Sharing cannot be enabled
31766 A certificate could not be found. Connections that use the L2TP protocol over IPSec require the installation of a machine certificate, also known as a computer certificate
31767 Internet Connection Sharing cannot be enabled. The LAN connection selected as the private network has more than one IP address configured. Please reconfigure the LAN connection with a single IP address before enabling Internet Connection Sharing
31768 The connection attempt failed because of failure to encrypt data
31769 The specified destination is not reachable
31770 The remote computer rejected the connection attempt
31771 The connection attempt failed because the network is busy
31772 The remote computer's network hardware is incompatible with the type of call requested
31773 The connection attempt failed because the destination number has changed
31774 The connection attempt failed because of a temporary failure. Try connecting again
31775 The call was blocked by the remote computer
31776 The call could not be connected because the remote computer has invoked the Do Not Disturb feature
31777 The connection attempt failed because the modem (or other connecting device) on the remote computer is out of order
31778 It was not possible to verify the identity of the serve
31779 To dial out using this connection you must use a smart card
31780 An attempted function is not valid for this connectio
31781 The connection requires a certificate, and no valid certificate was found
31782 Internet Connection Sharing (ICS) and Internet Connection Firewall (ICF) cannot be enabled because Routing and Remote Access has been enabled on this computer
31783 Internet Connection Sharing cannot be enabled. The LAN connection selected as the private network is either not present, or is disconnected from the network. Please ensure that the LAN adapter is connected before enabling Internet Connection Sharing
31784 You cannot dial using this connection at logon time, because it is configured to use a user name different than the one on the smart card. If you want to use it at logon time, you must configure it to use the user name on the smart card
31785 You cannot dial using this connection at logon time, because it is not configured to use a smart card. If you want to use it at logon time, you must edit the properties of this connection so that it uses a smart card
31786 The L2TP connection attempt failed because there is no valid machine certificate on your computer for security authentication
31787 The L2TP connection attempt failed because the security layer could not authenticate the remote computer
31788 The L2TP connection attempt failed because the security layer could not negotiate compatible parameters with the remote computer
31789 The L2TP connection attempt failed because the security layer encountered a processing error during initial negotiations with the remote computer
31790 The L2TP connection attempt failed because certificate validation on the remote computer failed
31791 The L2TP connection attempt failed because security policy for the connection was not foun
31792 The L2TP connection attempt failed because security negotiation timed out
31793 The L2TP connection attempt failed because an error occurred while negotiating security
31794 The Framed Protocol RADIUS attribute for this user is not PPP
31795 The Tunnel Type RADIUS attribute for this user is not correct
31796 The Service Type RADIUS attribute for this user is neither Framed nor Callback Framed
31797 A connection to the remote computer could not be established because the modem was not found or was busy
31798 A certificate could not be found that can be used with this Extensible Authentication Protocol
31799 Internet Connection Sharing (ICS) cannot be enabled due to an IP address conflict on the network. ICS requires the host be configured to use 192.168.0.1. Please ensure that no other client on the network is configured to use 192.168.0.1
Errors 32000-32200 (LDAP)
Error Description
32001 LDAP: Operations error
32002 LDAP: Protocol error
32003 LDAP: Time limit exceeded
32004 LDAP: Size limit exceeded
32005 LDAP: Compare false
32006 LDAP: Compare true
32007 LDAP: Authentication method not supported
32008 LDAP: Strong authentication method required
32009 LDAP: Referral V2
32010 LDAP: Partial results
32011 LDAP: Referral
32012 LDAP: Admin limit exceeded
32013 LDAP: Critical extension unavailable
32014 LDAP: Confidentiality required
32016 LDAP: No such attribute
32017 LDAP: Undefined type
32018 LDAP: Inappropriate matching
32019 LDAP: Constraint violation
32020 LDAP: Attribute or value exists
32021 LDAP: Invalid Syntax
32032 LDAP: Object not found
32033 LDAP: Alias problem
32034 LDAP: Invalid distinguished name syntax
32035 LDAP: Is leaf
32036 LDAP: Alias dereference problem
32048 LDAP: Inappropriate authentication
32049 LDAP: Invalid Credentials
32050 LDAP: Insufficint rights
32051 LDAP: Server busy
32052 LDAP: Server unavailable
32053 LDAP: Unwilling to perform
32054 LDAP: Loop detected
32064 LDAP: Naming violation
32065 LDAP: Object class violation
32066 LDAP: Not allowed on non-leaf entry
32067 LDAP: Not allowed on RDN
32068 LDAP: Already Exists
32069 LDAP: No object class modifications allowed
32070 LDAP: Results to large
32071 LDAP: Affects multiple DSAS
32080 LDAP: Generic Error
32081 LDAP: Server down
32082 LDAP: Local error
32083 LDAP: Encoding error
32084 LDAP: Decoding error
32085 LDAP: Operation timed out
32086 LDAP: Authentication unknown
32087 LDAP: Error in filter
32088 LDAP: User cancelled
32089 LDAP: Invalid parameter
32090 LDAP: Out of memory
32091 LDAP: Connection error
32092 LDAP: Operation not supported
32093 LDAP: No results returned
32094 LDAP: Control not found
32095 LDAP: More results to return
32096 LDAP: Client loop
32097 LDAP: Referral limit exceeded
32101 LDAP: Not connected to server
32102 LDAP: Failed to load WinLDAP library
Errors 33000-34399 (SMS and MMS Toolkit - Misc Errors)
Error Description
33003 Professional license required to use this function
33005 Invalid parameter passed to function
33035 Invalid message class
33036 Invalid message priority
33050 Failed to load provider config file, file not found
33051 Failed to load provider config file, file corrupt
33052 Failed to save provider config file, failed to write file
33060 No more messages in receive buffer
33061 Failed to query message, or invalid messagereference specified
33130 Device used is not a GSM device
33131 Device used does not support GPRS/UMTS
33140 There is no SIM card in the GSM device
33141 SIM card requires PIN code
33142 PIN code entered is invalid
33150 Selected message storage is not available on this GSM device
33151 Device used does not support the storage of SMS delivery report messages
33160 No network coverage, or network busy
33170 SMS service centre (SMSC) address not set
33171 Failed to set SMS service centre (SMSC) address
33201 Failed to connect to SMPP server, please check hostname or IP address
33202 Failed to bind to SMPP server, please check SystemID and Password
33203 Invalid SystemID specified
33204 Invalid Password specified
33205 Not bound to SMPP server, please connect first
33206 SMPP operation timed out
33207 Invalid System Type specified
33208 Failed to send message, currently bound as a receiver
33209 Invalid SMPP version
33210 Failed to cancel SMS message
33211 To receive a deliveryreport, you have to connect as transceiver, not as a transmitter
33215 Failed to submit the SMS message, SMPP provider rejected the message
33216 Recipient address blocked or nut supported by SMPP provider
33217 SMPP Throttling error, please reduce message throughput
33225 Insufficient message credits to submit SMS message
33230 Invalid TLV type specified
33231 Invalid TLV tag specified
33232 TLV parameter not found
33301 Error response received from provider
33302 Unknown response received from provider
33303 URL template for sending text messages not set
33304 URL template for sending data messages not set
33305 URL template for sending unicode messages not set
33460 Invalid UCP provider
33461 No response from UCP provider
33462 Provider reported a syntax error
33463 Provider rejected the message (NACK)
33501 Error during initial negotiation phase
33503 Sending messages to this pager are bared by the provider
33504 Invalid message
33505 Message was sent, but no (N)ACK received
33600 No SNPP provider specified, please check hostname or IP address
33601 Failed to connect to SNPP provider, please check hostname or IP address
33602 Invalid SNPP password
33603 Invalid Pager ID or pincode
33610 SNPP command not supported
33611 No response from SNPP provider, operation timed out
33710 No connection to GPRS/UMTS network, please connect first
33711 Failed to create Dial Up Networking entry for the GPRS/UMTS connection
33712 Generic Dial-up networking error
33720 Missing MMSC server address
33721 Missing GPRS access point name (APN)
33722 Missing WAP gateway address
33730 No response received from WAP gateway
33731 Error response received from WAP gateway
33761 MMSC response: unspecified error
Error-codes-in-activex-controls
Activex-error-codes-1
Activex-error-codes-2
Activex-error-codes-3
Blog-post
Activex-error-codes-4
Activex-error-codes-5
Activex-error-codes-7
Datatable-to-excel-workbook
إرسال تعليق